Yale offers a comprehensive range of alarms to help keep you and your family safe and secure. No matter how well your property is secured with locks, fitting an alarm system will add peace of mind and an additional level of protection to your home of alarms for all levels of security.

Getting Started

How do I install my HSA6200 Standard Alarm?

Please refer to the Installation Manual included in your purchase, or view Yale's 'how to install' guide on YouTube.

Using you HSA6000 Smart Home Alarm

How often will I have to change the batteries in my alarm system?

Batteries should be replaced every 2-3 years. Each detector, siren, control panel will inform you when this is required.

Should the red light flash on my PIR?

The red PIR lights will not always flash, to conserve the battery life. If you are in any doubt of the operation of a PIR, vacate the area for up to 60 seconds, and test using the ‘walk test’ facility.

Can I add accessories to my alarm system?

Yes, any accessories from the HSA6000 range; however NOT from the Easfit EF- or SR- range.

Can I extend my entry time?

Not on this system, 20 seconds are as a default for every device. However, arming using the Key Fob will not give you any entry time at all, which means you will need to disarm outside the property. 

Can I have an internal sounder, on this alarm?

This feature is not available for this system. 

Can I part arm my system, using the HOME button on the keypad?

This feature is not available for this system. 

How do I reset the Key Pad PIN code?

The Key Pad is tamper protected. Please ensure that the siren tamper is disabled before you open the Key Pad cover then follow the below procedure:

• Open cover and remove battery. Reinsert with the number “3” key pressed (taking care 3 is held down).

• The Key Pad will go back to the “0000” Key Pad code.

• The Key Pad will now have to be re-learnt into the Siren

How do I disarm my system?

Key Pad: Press Disarm followed by your PIN code.

Key Fob: Press Disarm.

(The siren will beep twice and flash.)

How do I arm my system?

Key Pad/Key Fob: Press Arm

(The siren will beep/flash once. No audible countdown.)

Please note: the Key Pad will arm the system with a 20 second exit period. All detectors will be ignored (except for the tamper switches). The system can be

armed when inside the protected area of your premises.

Please note: the Key Fob will arm the system instantly without a 20 second exit delay. Any detector activated afterwards will trigger an instant alarm. The system should be armed when outside the protected area of your premises.

How do I expand my alarm system?

You can expand your alarm system to include up to 20 wireless alarm accessories:

  • Door/window contact
  • PIR Pet freindly motion detector
  • Panic button
  • Outdoor PIR pet friendly motion detector
  • Remote control
  • Smoke Detector
  • Remote keypad
  • Responce company link-up module
  • Repeater module

These accesories are available to purchase at www.yaleshop.co.za


Why does the Siren make an interrupted tone when sounding an alarm?

This is because the Siren has low batteries. Change batteries with new alkaline replacements. 

Why does my Siren not respond to the Key Pad?

This could be for a number of reasons.

  • Key Pad may have a low battery or bad connection. Check the battery connections and polarity, if OK replace the battery.
  • Siren batteries may be completely exhausted. Check Siren batteries by removing the Siren cover, if there is no tamper alarm when removed, replace the batteries
  • with new alkaline equivalents.
  • Key Pad not learnt-in. If Siren produces a tamper alarm when the cover is removed, and the Key Pad is OK, learn-in the Key Pad.
  • Siren could be out of radio range.
Why is the LED flashing on my Key Pad when any key is pressed?

This means that the battery is low. Please change it following this procedure:

  1. Switch off tamper protection (this process can be found here in the installation manual on page 9, Table 1.) link to manual found on this page https://www.yale.co.uk/en/yale/couk/productsdb/alarms/-ef-series-alarms--accessories/Standard-Alarm-Kit/
  2. Unscrew the two Key Pad case screws and remove Key Pad back to reveal battery.
  3. Using a screwdriver gently lever out the old battery.
  4. Insert new CR2032 coin cell battery with the + side uppermost
  5. Press battery into holder firmly with finger and thumb until a click is heard
  6. Press a number key and check that the LED lights. If the LED lights the new battery installation is successful, screw the Key Pad case back on and the battery change is complete.
I cannot get anything to learn into the siren

This will be because the siren DIP switch number 4 is off. This needs to be in the ‘on’ position.

Why is my siren not triggering?

Check that the Key Pad is programmed. By arming the system you should hear one beep to acknowledge the system is armed.  If you do not hear this please follow the instructions to re-learn keypad from the manual. 

My PIRs are not flashing on detection

They are not designed to flash on detection generally. They will only flash to warn a low battery in the device. 

My keypad will not disarm the system. It arms correctly, I hear the single siren confirmation ‘beep’, but why will it not disarm to give two ‘beeps’?

Please check your keypad PIN has been correctly set, it may still be stuck at the factory preset code. Try changing to your desired code again, taking care to not leave any gaps between the stages of the PIN setting process.

I am installing my Yale siren-based alarm, but I cannot disable the siren tamper. Why is this?

Your keypad may not be programmed in correctly to the siren. Ensure that the keypad program mode green LED is flashing when transmitting a tamper-off signal and the confirmation ‘beep’ is heard. If the problem persists, try re-‘learning’ your keypad, ensuring that the siren master/slave switch ‘4’ is set to ‘on’ and that you are in the ‘keypad programming’ mode.